Customer Favorites

Replacement M4 T20 Hollow Torx screw for TPMS valve stems.

The picture is not an accurate representation.The required scrutineering kit from Bosch for teams competing in either GTP or GTD Pro/GTD.Kit contains the MS6 SCR logger, USB, VMPS and Antenna.There is currently an extended lead time on the MS6 kits due to manufacturer delays. We...

This 4 way connector is designed to mate to Bosch Motorsport Ignitors, and comes with the connector, 18ga terminals and straight boot.

Connector and pins to make your own wiring harness for various models of Motec ECU's. These are for the 26 way connectors on the M800/600/400 , M84, and Connector D on M1 Series ECUs.Backshells are used to provide a better surface to grip shrink boots...

Description Technical Data Single Antenna Receiver Control Unit (known as an RCU) is a system for real-time detection, monitoring and transmission of tire pressure and temperature data.  The RCU is equipped with a free wire output and can interface with the vehicle logger via CAN line...

For C60 Data Logger USB Interface

A significant upgrade over standard fuel pressure regulators, the Bosch Mini Fuel Pressure regulator is rated for both gasoline and methanol and features a higher pressure range  and return flow rate. 30 to 400 l/h reflow Adjusted at 105 l/h Aluminum housing  All versions...

Full Application Programming Interface for Bosch Darab V7 for 1 year from date of purchase. Must be renewed annually.

Description Documentation • ABS Wheel Speed Sensor Interface • Lightweight Aluminum Housing • All Bosch Motorsport ABS systems are for competition use only and are NOT legal on public roads. Bosch Motorsport has developed a wheel speed module that converts the Bosch DF11 (differential dual...

Description Documentation • Wide measurement range: -40 to 140°C • Air temperature measurement • Robust design This sensor is designed to measure air temperature e.g. in the air box or ambient temperature. The signal may be used as a control value for engine control...

Description Documentation • Wide measurement range: -40 to 130°C • Robust design This sensor is designed to measure fluid temperatures e.g. oil, water or fuel. This signal may be used as a control value for engine control units or as a measurement value which...

6 Position switch for Bosch Data Loggers and ECU applications. These are built to specification, please indicate required lead length from 15-95cm when placing your order

Tyre Watch - High performance material to endure centrifugal stress. Simple and robust concept to adapt the sensor on all rims standard nuts and external rim. Available Configurations: 1. with no valve stem 2. with 16mm L-valve stem

Replacement IMU for Bosch M5 ABS systems with 1mb/s CAN speed. This sensor is for ABS system only. MM510 sensors for general applications can be found here: ACCELERATION SENSOR MM5.10

Description Technical Data Two Antenna Receiver Control Unit (known as an RCU) is a system for real-time detection, monitoring and storage of tire pressure and temperature data. Consisting of multiple components (which can be ordered separately or as a kit) the auto racing version...

Bosch Motorsport IMU Sensor MM5.10 A 5 degree-of-freedom inertial measurement unit combining three linear accelerometers and two rotational rate sensors in one compact housing, streaming vehicle dynamics data over a 1 Mbaud CAN bus. Overview What Is It Five channels of vehicle dynamics data...

Description Documentation • 2-axis rotation rate (yaw rate, roll rate) • 3-axis accelerometer (X, Y, Z) • 1 Mbaud or 500 kBaud CAN-output • Aluminum housing • Integrated motorsport connector The MM5.10-R was designed to measure the physical effects of rotational and linear acceleration....

Knock Sensor with flying lead, Mounts with a M8 bolt. Uses the LK3 connector

225l/h @ 4bar in-tank pump - 38mm diameter body. This pump has been discontinued and has been replaced with F02U.454.100-01

Developed by Deutsch from the MIL-C-38999 Series 1.5 (Eurofighter connector), the Deutsch AS Series is a range of medium and high density circular connectors designed to meet the stringent requirements of the autosport industry. Foremost of these requirements are enhanced performance with both weight...

The Deutsch DT06-4S-E008 Plug comes with the connector, wedgelock and sockets. The DT series are an industry standard size 16 contact connectors, which are rated for 13 amps continuous and will accommodate wire sizes from 14-20 AWG and has a silicon rubber seal. Deutsch DT06-4S-E008 Receptacle Includes:1x - Male Connector1x - Wedgelock...

The Deutsch DTM04-12P-E003 Receptacle comes with the connector, wedgelock and pins. The DTM series are an industry standard size 20 contact connectors, which are rated for 7.5 amps continuous and will accommodate wire sizes from 16-22 AWG and has a silicon rubber seal. Deutsch DTM04-12P-E003 Receptacle Includes:1x - Female Connector...

The Deutsch DTM04-2P-E007 Receptacle comes with the connector, wedgelock and pins. The DTM series are an industry standard size 20 contact connectors, which are rated for 7.5 amps continuous and will accommodate wire sizes from 16-22 AWG and has a silicon rubber seal. Deutsch DTM04-2P-E007 Receptacle Includes:1x - Female...