Bosch Motorsport

Description Documentation • User-friendly interface • Customer-defined features feasible • Prepared for test automation • Favorable test setup, consuming low space • Simulation of typical automotive interfaces combined in one unit The new and modern hardware-in-the-loop test system µLC Test System is suitable for...

12 Position switch for Bosch Data Loggers and ECU applications. These are built to specification, please indicate required lead length from 15-95cm when placing your order

Replacement IMU for Bosch M5 ABS systems with 500kb/s CAN speed. This sensor is for ABS system only. MM510 sensors for general applications can be found here:ACCELERATION SENSOR MM5.10

Replacement IMU for Bosch M5 ABS systems with 1mb/s CAN speed. This sensor is for ABS system only. MM510 sensors for general applications can be found here: ACCELERATION SENSOR MM5.10

This sensor is designed to measure temperatures up to 300°C of oil, water, fuel or air. This signal is used as a control value for engine control units or as a measurement value which is logged in a data acquisition system. The NTC-sensing element...

Description Documentation • Wide measurement range: -55 to 300°C • Very short response time • Strong protection against ambient temperature • Compact and robust design This sensor is designed to measure temperatures up to 300°C of oil, water, fuel or air. This signal is...

40 to 140degC range- Suitable for air- Jetronic 2-pin connector- O-ring seal- Flange mount with M6 hole- Very fast response- OE quality and performance

Description Documentation • Absolute fluid or air pressure measurement • Measurement range 3.5 to 700 bar • High robustness against vibrations • Compact design • Analog output This sensor is designed to measure absolute pressure of various kinds of media e.g. Diesel, gasoline, water,...

Description Documentation • Absolute fluid or air pressure plus temperature measurement • Measurement range versions 3.5 to 700 bar • Temperature measurement: PT1000 • High robustness against vibrations • Analog output This sensor is designed to measure absolute pressure of various kinds of media...

Direct mount knock sensor. Uses a M8 Bold and LK2 connector

Description Documentation • Engine vibration measurements • Measurement range 3 to 25 kHz • Robust design • Compact housing This sensor is used for detecting structural born vibrations in spark ignition engines due to uncontrolled combustion. This sensor is suitable for operation in extreme...

Description Documentation • Max. 35 kV • Max. 90 mJ • Especially developed for Turbo-GDI engines • Max. 15,000 1/min • Connection for high voltage wire This single fire coil was developed for the use e.g. in GDI (turbocharged) high performance engines. It is designed...

Description Documentation Software • Supply of up to 4 Bosch lambda sensors, type LSU ADV • Integrated voltage compensation for sensor heater The Lambdatronic LT4 ADV is a control module which function is to supply and control up to four Bosch LSU ADV. The...

Description Documentation Software • 120 A continuous current • 36 outputs • 80 A high side switches • Easy programming of complex functions • Software-tool integrated The PowerBox is an intelligent control and distribution unit for the electric grid in a modern racing car...

Full Logging Stage 2 Upgrade for DDU 8, DDU 9, DDU 10 Displays as well as C60 and C70 Loggers.This software enable code (entered using RaceCon while connected to the dash module) increases the logging memory by 1GB to the existing system memory. Note: Stage...

Full Logging Stage 1 Upgrade for DDU 8, DDU 9 and DDU 10 Displays/Loggers This software enable code (entered using RaceCon while connected to the dash module) increases the logging capability from 50Hz and 100 Channels, to 1080 channels at a maximum logging rate of...

Software Code for DDU 9 and DDU 10.  Codes are entered via Race-Con to enable the following features: Enables 12 analog inputs for DDU 9, DDU 10, C70 Enables an additional 2 CAN interfaces for the DDU 10.

Software unlock code to enable the 2nd (yellow connector) on the C60 logger. This upgrade allows the end user to add the following: 20 x Analog inputs1 x GPS Input4 x Speed Inputs (Hall or Mag)

Description Documentation Software Offering a completely brand new library of graphic elements, the Bosch DDU 10 display is a fully customizable dashboard display and motorsport logging system, allowing the end user to design and customize the twelve different display pages. Additionally, a configurable input activates the...

Description Documentation Software • Compact and lightweight data logger • Aluminum housing • Recording on USB flash drive (opt.) • Two motorsports connectors The data logger C 70 is a compact and lightweight data logging system for motorsport applications. This allows for synchronized acquisition...

PBX90 Primary Power Connector 8MM Stud for use with 35mm2 Wire

Bosch Compact 3 Pole Connector kit (Code 1) with "clean exit" No boot collar. No Stocked-Long lead times.

Compact 3 Connector Kit Code 1. Has boot collar, no protective shroud.